<% startup_id = request.querystring("sid") if startup_id = "" then startup_id = 0 sql = "select * from startup where startup_id > 0" set rs = conn.Execute(sql) on error resume next %> Lynx Power RMA
Lynx Power Systems
1270 Shiloh Road, Suite 100
Kennesaw, Georgia 30144
Phone: 770-499-0439
Fax: 770-499-24798
Genset Start-Up Acceptance Test and Warranty Commencement Document

Performed By: <%=rs("Performed_By")%> Date: <%=rs("entry_date")%>
Customer Name: <%=rs("Customer_Name")%>
Installation Location: <%=rs("Installation_Location")%>
Model Number: <%=rs("Model_Number")%> Serial Number: <%=rs("Serial_Number")%>
Genset Placement:  >Indoor  >Outdoor
Application:  >Continuous Standby  >Prime Power
 >Other <%=rs("App_Other_text")%>

Pre-starting Check List:
 >Oil Level  >Radiator Fluid Level  >Battery Fluid Level  >Ventiation  >Belts & Hoses Tight
 >Main Output Leads Wired Correctly  >Remote Start Leads Wired Correctly
 >Fuel Line Sized & Installed Correctly  >Remote Annunciator Leads Installed Correctly
 >Unit Grounded, Location: <%=rs("PS_Location")%>
Start Unit For Testing:
 >Main Line Circuit Breaker Off  >Reset DC & AC Control Breakers  >Bleed Fuel Lines
 >Connect Battery  >Start Unit  >Check For Noise Or Vibration
 >Check Oil Pressure  <%=rs("SU_Check_Oil_Pressure_val")%>   >Water Temp  <%=rs("SU_Water_Temp_val")%>
Check and Record the Following:  >DC Voltage  <%=rs("SU_DC_Voltage_val")%>   >AC Voltage   <%=rs("SU_AC_Voltage_val")%>
 >AC Frequecy   <%=rs("SU_AC_Frequency_val")%>
Fault Sensor Check:
 >Ground Oil Pressure Sensor   >Ground High Engin Temp
Restart Engine AFter Each Fault Shutdown Allow Engine To Riun for 15 Minutes After Final Check and Record
 >Oil Pressure <%=rs("FS_Oil_Pressure_val")%>    >Water Temp   <%=rs("FS_Water_Temp_val")%>    >DC Volts   <%=rs("FS_DC_Volts_val")%>
Check Automatic Operation (If Supplied by Lynx Power Systems):
 >Turn Main Line Circuit Breaker On  >Set ATS To Transfer Inhibit  >Start GenSet
 >Check For Proper Rotation At ATS  >Set Genset & ATS To Auto Position
 >Stimulate Power Outage - Turn Off Normal Source Breaker
 >Voltage Phase 1   <%=rs("AO_Voltage_Phase_1_val")%>  >Amps Phase 1   <%=rs("AO_Amps_Phase_1_val")%>
 >Voltage Phase 2   <%=rs("AO_Voltage_Phase_2_val")%>  >Amps Phase 2   <%=rs("AO_Amps_Phase_3_val")%>
 >Voltage Phase 3   <%=rs("AO_Voltage_Phase_4_val")%>  >Amps Phase 3   <%=rs("AO_Amps_Phase_4_val")%>
 >Frequency Under Load   <%=rs("AO_Frequency_Under_Load_val")%>  >Oil Pressure   <%=rs("AO_Oil_Pressure_val")%>
 >Engine Temp   <%=rs("AO_Engine_Temp_val")%>  >Check For Noise and Vibration   <%=rs("AO_Check_For_Noise_val")%>
Return The Normal Circuit Breaker To The On Position & Check the Following:
 >Time Delay To Re-transfer   <%=rs("AO_Time_Delay_To_Retran_val")%>  >Cool Down Time Delay   <%=rs("AO_Cool_Down_Time_Delay_val")%>
Automatic Transfer Switch (If Supplied by Lynx Power Systems):
Make: AT_Make<%=rs("AT_Make")%> Model Number: AT_Model_Number<%=rs("AT_Model_Number")%>
Serial Number: <%=rs("AT_Serial_Number")%>
 >Two Pole  >Three Pole  >Four Pole  >Open  >NEMA  >NEMA 3R
 >Other <%=rs("AT_Other_val")%>
Battery Charger (If Supplied by Lynx Power Systems):
Make: <%=rs("BC_Make")%>       Model: <%=rs("BC_Model")%>       Amp Rating: <%=rs("BC_Amp_Rating")%>
Completion:  >Running Time Meter Reading <%=rs("Running_Time_Meter_val")%>
Suggestions: <%=rs("Suggestions")%>
Start-up Acceptance Test Completed By: <%=rs("Completed_By")%>
Date: <%=rs("Completed_Date")%>